It is very comfortable to live in a house where the temperature, humidity and oxygen concentration meet established standards. To do this, you need to make a high-quality air exchange system. One of the conditions for its trouble-free operation is a properly assembled and installed ventilation duct on the roof, in which there are channels for air outflow.
The task of organizing air exchange is not new, therefore, there are time-tested solutions, following which you can perform all the work of installing the box yourself. To do this, you need to read the instructions written by us, prepare the tool and material, gather your courage and start.
We paid attention to some theoretical aspects of the placement of ventilation outlets and provided illustrated instruction on how to create a duct. All stages are designed for a person who has initial skills in working with a conventional building tool. No specific knowledge or skills will be needed.
Rules for placing ventilation outlets
There are two standard ways of venting pipes outside the house: through the wall and through the roof. In the second case, pipe fragments located above the roof level are often placed inside a special box.
The ventilation duct has two functions:
- Warming. When cooling the air leaving the room, condensation forms. It begins to seep back through the ventilation system, and can also narrow or completely close the channel section.
- Waterproofing. Violation of the integrity of the roof can lead to water entering the attic space. It is also necessary to protect the ventilation duct from direct ingress of precipitation in the form of rain or snow.
And also the box will serve as an excellent supporting structure for fastening the facing material and to ensure the indentation from unstable building structures made of lumber.
The box on the roof of the house should look harmonious. Therefore, you need to think through its design in advance: colors and decorative elements
If several ventilating exits to the attic are planned or already implemented in the house, then there are 3 options for how to bring them to the roof:
- For each channel, you can make your own box. This is the most costly method, but in this case it is possible to remove pipes without bending, which with natural ventilation increases traction.
- To bring all the pipes together and bring them to the roof in one box. This reduces the amount of work on the roof, but increases the workload of the attic.
- Make a single system of ventilation ducts with one output. This minimizes the size of the duct, which greatly simplifies work on the roof, but can lead to problems characteristic of branched air exchange systems.
The use of a channel system with several places of air intake and one point of its removal should be previously well calculated. It is necessary to properly build the ventilation and install check valves, otherwise reverse air flow is possible.
The hole in the roof should not damage the rafters, otherwise this will lead to the risk of redistributing the load of the supporting structures. The crate does not play such an important role, since it only holds the coating.
Since there can be many ventilation pipes, you need to place them in the attic so that they take up little space
You also need to carefully approach the issue of determining the location of the ventilation outlet so that it does not appear in the zone of wind backwater.
Failure to comply with the rules for the position of the pipes relative to the roof elements specified in clause 6.6.12 of SNiP 41-01-2003 “Heating, ventilation and air conditioning” can lead to a decrease in draft or its capsizing, which will immediately affect air exchange.
Using this scheme, you can determine the sufficient height of the ventilation outlets on the sloping roof of the house. If there are tall objects nearby, then the calculations will be more complicated
Therefore, for a pitched roof, it is better to plan a place for the box closer to the ridge. This will reduce the height of the structure, which will simplify the work on its construction.
Steps for installing the box
After a place has been chosen for the passage of ventilation pipes through the roof, it is necessary to carry out all the work in the attic (bring the pipe or pipes) and only then proceed with the construction of the duct. This procedure is typical of private houses, so the different options are well researched and you can offer a standard solution that is suitable for almost any situation.
Necessary materials and tools
Before deciding on their own to make a ventilation duct on the roof, it is necessary to understand that this event will last at least one daylight. Therefore, you need to know the weather forecast to be sure that there is no rain or wind.
Any work on the pitched roof must be carried out in accordance with safety requirements. To do this, you must:
- have a safety rope tied to a belt;
- wear the right shoes that do not slip and do not fly off your feet;
- install two stairs on the roof slope on the sides of the place where the box will eventually stand.
Neglect of safety regulations may lead to the absence of a roof box in the near future, due to the installer getting into the trauma department of the hospital.
Ideally, the climb to the roof should look like this. But usually on the roof they put an ordinary staircase with an attached corner that holds on to the ridge
During the work, the following tools will definitely be required:
- heavy hammer;
- screwdriver;
- saw on wood;
- scissors for metal;
- knife and scissors for soft materials and films;
- level;
- grinder (in the case of covering the roof with galvanization or metal).
It is also necessary to take care in advance of a sufficient number of wood screws, scotch tape, small nails and other consumables.
Roof Hole Cutting
To accurately determine the position of the hole, it is necessary to drill 4 holes from the inside at the corners of the future box. Then, using a ruler, you need to draw a contour and begin to cut it.
If the coating is metal, then you need to use a grinder or scissors for metal. You can remove roofing material or other “soft” material with any suitable tool: a knife, scissors, jigsaw.
If it is possible to save some plank boards without damage or with minor cutouts, then this must be done
It is easier to remove a continuous crate with a jigsaw, but you can also use an ordinary saw. Before doing this, it is better to determine the inside of the place of attachment of nails and screws, so as not to “catch” them.
Wood frame formation
The frame can be made of edged boards with a thickness of 35 mm (there is no sense in a larger thickness) or a bar 50 × 100 mm. Vertical racks should rest on the floor of the attic, and not be attached to the crate or rafters, since the box will have a lot of windage and can be demolished by the force of the wind.
Above the roof, the frame is tied at the top and a stiffening belt is additionally installed at the roof level. It will also serve as the basis for fastening the skin.
After the construction of the frame, the pipes are extended from the attic to the top of the constructed box. If the ventilation system is made of branded elements, then in this procedure there is nothing complicated.
If the pipes are not made of metal, it is better to install them after assembling the frame, since the plastic is easily susceptible to impact and can be broken during operation
It is imperative to expose the pipes exactly vertically, as well as to monitor their symmetrical location inside the box. It is necessary to comply with the condition that from the pipe to the edge of the box there should be at least 5 cm of space that will be filled with insulation. And the top should be set exactly, for which you will need to use the level.
Thermal insulation
Before laying the insulating material, you need to hem the boards that cover the box from below at the level of the attic ceiling. This must be done so that the insulation does not fall down.
Since it is impossible to lay solid material in the box, two options remain:
- freely deformable material such as mineral wool;
- bulk material such as perlite sand fraction 0.16 - 1.25 mm.
Expanded clay (insufficiently low thermal conductivity), polystyrene foam (coarse-grained), sawdust (can rot) are not suitable for this purpose.
Mineral wool must be laid very tightly so that there are no cold bridges. Therefore, in units of volume, its consumption will be almost two times more than the space of the box filled with insulation.
Mineral or basalt wool is easier to lay when the box is still in the form of a frame. Cramming material between stiffeners and the wall will be quite difficult
Perlite is very “fluid”, so it perfectly fills all the voids. But so that it does not leak out, inside the box will need to be laid with a dense fabric such as geotextiles. You need to work with perlite in goggles and a mask, especially if there is wind on the roof. After backfilling, it is better to immediately put a layer of mineral wool or polystyrene with holes under the pipes, since perlite can inflate.
It is necessary to sheathe the frame with an OSB-plate or board, thickness 1.0-1.5 mm. To save time, you may want to cut out the side walls in advance according to the dimensions calculated for the box. However, practice shows that this is not worth it. When installing the frame, unforeseen deviations often occur, which will slightly change its dimensions.
After warming the mineral wool and installing the walls, the box looks like this. The insulation must be flush with the vents
If the walls of the ventilation duct will be assembled from several elements, then you need to remember that there is no special need for a snug fit of joints. Therefore, time does not need to be spent on fitting.
Waterproofing the ventilation duct
One of the dangers for a type of mineral wool insulation is the ingress of water into it and its subsequent freezing. Therefore, it is necessary to perform vapor barrier.
For waterproofing, a reinforced polyethylene film or a polymer membrane is used. It is desirable to impose it in one piece
In the center of the piece of waterproofing material, you need to cut a hole 2 cm smaller than the diameter of the pipe. Then, cuts should be made along the inner edge, not more than 1 cm deep. When put on a pipe, such an element will close the gap between it and the ramp plane tightly.
The top of the film can be crushed with polystyrene foam, cutting holes for pipe outlets. After that, the upper part of the box must be reinforced with a mesh and cement.
Polyfoam and mineral wool are better closed with cement. Otherwise, the birds will reach them and try to pull them into nests. In this case, insulation and vapor and waterproofing will be violated. Before laying the coating, the area around the outlet of the ventilation pipe is covered with a waterproofing carpet
If the pipes are below the level of cement, then you need to add inserts. To prevent this situation from happening, it is better to immediately install the ventilation outputs with a margin of height (10-20 cm), since it is easier to cut off excess than to deliver additional fragments.
Providing waterproofing of the base and sides
When it rains or snow melts, streams of water flow on the roof. With great care, it is necessary to carry out work to prevent them from falling under the ventilation duct.
There is a rule that ensures that water does not fall, when it flows freely along an inclined surface: the upper waterproof element must be pulled over the lower one. According to this postulate, the design of the waterproofing of the ventilation duct located on the roof is arranged.
The outer side of the rib, which will be facing down, must be smeared with a liquid roofing material or glued to it with a double-sided bitumen tape. Then no spray will fall under it
First, you need to nail the abutment strips to the base of the box. They have the appearance of corners with a width of the edge of 5-7 cm. It is better to fix them not on nails or screws, but on bitumen mastic or liquid roofing material.
The bar, which will be on the side closest to the ridge, must be pushed under the roofing. Then the water will not flow under it, into the under-roof space and into the attic
As a waterproofing that protects the sides of the ventilation duct, it can be roofing, soft tiles, rolled bitumen and bitumen-polymer roofs, polymer membranes, galvanizing or any other durable material with water-repellent properties.
If it is not solid, then it must be fastened from the bottom so that the upper parts are layered on the lower.
The ventilation shaft, equipped with a box, can be finished with any material, including flexible bituminous tiles and similar rolled material. After upholstery waterproofing box will look like this
If desired, you can install an additional visor in the middle, although if the deflector for ventilation pipes, grouped in one shaft, will have large protrusions, then there will be no sense in it.
Corners must be covered with a metal or plastic corner (with a rib width of 5-7 cm), which should be placed on top of the waterproofing. This is the easiest solution.
If a soft material was used for cladding, then it is advisable to coat its joints with some adhesive. A liquid roofing material is suitable for this. This is necessary so that a strong wind does not disrupt the waterproofing over time.
Umbrella installation and fixation
There are 2 options: order a visor from manufacturers or make it yourself. As in the case of the sidewalls, you do not need to make an umbrella deflector for the duct in advance, since the dimensions of the constructed object may differ from the calculated ones, which will lead to the problem of matching parts.
You can order a visor from companies engaged in the creation of metal products. It is necessary to measure the external perimeter of the upper part of the ventilation duct, select the color and shape of the cover. Usually the production time takes 1-2 days. For this period, you need to cover the ventilation with a temporary cap, for example, from plywood with a roofing material nailed on top of it.
You can make the simplest cap of metal yourself. To do this, you will need corners, a sheet of metal 1.0-1.5 mm thick and the ability to work with welding
Also, the cap can be fixed on the vertical bars that make up the frame of the entire ventilation duct. In this case, they should initially be 20-30 cm higher than the pipe outlet. The deflector can be made single-piece from a wooden shield, coated on top with a galvanized sheet. With this solution, it is not necessary to have a welding machine and the ability to work with it.
All wooden parts of the lid should be coated with anti-fungal impregnation or weather-resistant paint for external work, for example, PF-115. At the end of the installation, you need to check that the installed visor does not stagger, otherwise the wind will gradually loosen the mounts.
Continuation of the previous video. Part 2 - insulation, metal sheathing and water drainage:
Two technical solutions for waterproofing the box, depending on its proximity to the ridge or cornice:
The main stages of installation of the ventilation duct are the same for any conditions: creating a hole, installing a reliable frame, insulation, waterproofing, lining, manufacturing and fixing of the deflector.
The nuances of the job are to cover the roof, as well as the type of material from which the entire structure will be assembled. In most cases, you can do everything yourself, having initial skills in construction or repair.
Do you have useful information on the topic of the article, which is worth sharing with site visitors? Do you want to tell how the ventilation shaft was equipped with a duct in your own cottage or in a country house? Write comments, please, in the block form below, ask questions, post pictures on the topic of the article.