Now most consumers of utility services are provided with metering devices, since paying for water on the meter has become much more profitable than on a common basis.
You can calculate the amount of payments yourself. To do this, you need to calculate the flow rate, know the tariffs, and also understand that in addition to water supply, there are other services that are affected by the readings of water meters.
Next, we will tell you how to correctly make calculations and pay for water supply.
Calculation of water consumption
To accurately calculate the water consumed at the facility, meters are installed. They are placed on pipes, which serve both hot and cold water. As a rule, installation work is carried out by specialists of a water supply organization or management company, since the devices will need to be sealed.
Read more about how the installation and sealing of meters occurs.
Periodically, representatives of organizations providing housing and communal services, inspect metering devices for the safety of seals and the absence of visual problems with the functioning of the devices. The owners of the premises are obliged to allow inspectors to the installation site of meters. Also, meters must undergo mandatory verification, the terms of which are indicated in the technical documentation for the device.
Counters are installed in the area of responsibility of the user of services - in an apartment, private house or non-residential premises. If there are several pipes through which water is introduced, then all of them must be equipped with a metering device.
Hot and cold water meters differ in case color - red and blue, respectively. This helps to avoid confusion when taking readings.
Every month at a certain time, the owners take readings. Each water meter has a dial that shows the volume of fluid passed through it.
It can provide data with different accuracy:
- if there are only 5 black digits on the dial, then the displayed number is the number of cubic meters;
- if in addition to 5 black numbers there are 3 more red numbers, then the displayed number is the number of liters.
In any case, to pay for utilities, the consumer needs to take readings accurate to a cubic meter, so the red numbers (if available on the instrument’s dial) need not be taken into account.
The current reading of this meter is 133 liters or 0.133 m3. Existence of accuracy of up to 1 liter allows you to independently check the device for the quality of measurements using tanks of known cubic capacity
Since it is necessary to calculate the volume of water on the meter per month, it is necessary to subtract the previous ones from the current readings. And so it is necessary to do for each meter, then adding the data separately for cold and hot water.
For example, if there are two cold water inlets and the meter readings for the previous month are 312 and 445 cubic meters, and for the current month - 316 and 450, then the total consumption (V) will be equal to:
V = 316 + 450 - 312 - 445 = 9 m3
In order not to be mistaken in the calculations, you can keep a special house log in which to record the readings of meters for water, electricity, gas and heating. If the information on the previous testimony is lost, then it can be found by contacting the organization that accepts payments.
Calculation of the cost of the counter
It is possible to calculate the amount necessary for payment for utilities related to water, independently. But for this you need to know the tariffs and some nuances of charges, which are then displayed in the payment.
Hot and cold water supply
Organizations provide water supply services to the population in accordance with established tariffs. Payment of hot water according to meter readings is much more expensive than cold (3-8 times), as companies need to compensate for the cost of servicing communications and heating water.
Tariffs are constantly changing and depend on the region and service provider. The exact value of the cost of a cubic meter of hot and cold water can be obtained from the organization with which the water supply agreement was concluded, or by contacting the housing and communal services committee of the district or the local administration.
Rates are also published on the website of the administration of each subject of the Russian Federation. Having access to the Internet, the easiest way to get information on prices for utilities
Suppose that the total consumption of cold water per month was 6 m3and hot - 4 m3. The tariff for water supply established by the administration is 22.77 r / m3, for hot water supply - 132.69 r / m3.
In this case, the total amount for water supply (R) will be equal to:
R = 6 * 22.77 + 4 * 132.69 = 667 rubles. 38 kopecks
Sometimes instead of the tariff for hot water, expressed in r / m3 indicate another parameter - the cost of heating water r / Gcal. It is possible to independently calculate the number of gigacalories spent on heating one cubic meter of hot water only with a known value dt - temperature difference between cold and hot water. This also includes heat loss that an ordinary consumer cannot measure.
Therefore, accurate calculation with such data is not possible. But approximately 0.050 - 0, 065 gigacalories are expended on the heating of one cubic meter in the middle zone of Russia. Thus, it is possible to calculate the range of the amount to pay for water services.
Let with the same consumption of cold water 6 m3 and hot 4 m3 the cost of water supply is 22.77 r / m3, and the price per gigacalorie is 1827 r / Gcal.
Then the amount for water supply will be within the following range [R1, R2]:
- R1 = 22.77 * 6 + (22.77 + 1827 * 0.050) * 4 = 593 rubles. 10 kopecks;
- R2 = 22.77 * 6 + (22.77 + 1827 * 0.065) * 4 = 702 rubles. 72 kopecks
In many houses, it is much more economical to install a boiler for heating hot water in the plumbing system or heating circuit. In this case, the tariff will be floating. It will depend on the cost of cold water supplied and the cost of heating it.
Boiler rooms with modern equipment significantly save the cost of hot water. Even taking into account the costs of their periodic maintenance
The consumer, as well as in the case of centralized supply, will need to take readings from the meters and provide data on water consumption to the organization responsible for managing the house.
Wastewater and general household needs
In private houses and cottages, the cost of paying for cold water according to the meter is often the only water utility services. In apartment buildings, this is not so.
All water entering the apartment leaves through the sewer. Drainage also requires financial costs for pipeline maintenance and cleaning activities.
There is no need to install meters on the sewer, since the drain volume is equal to the total amount of hot and cold water received. Knowing these indicators and the tariff for the service, you can calculate its cost.
Water disposal is also referred to as housing and communal services, tariffs for which are approved by state authorities. Paying for a cubic meter of sewage discharge is 2-5 times cheaper than for supplying cold water
Another type of water-related costs incurred by the owner of the property in an apartment building is the payment of the maintenance of common property (SDI). Previously, this column in receipts passed under the acronym ODN (common house needs). But the meaning of these payments remained the same.
When summing data from individual water meters, the volume of consumed water is obtained slightly less than the general metering device shows.
This occurs for the following reasons:
- the costs of washing floors in the entrances, watering the lawns in the adjacent territory and other needs;
- pipe leaks within the boundaries of the house;
- underestimation of indicators of water consumption or lack of data on part of the premises.
To compensate for these costs, water shortages are distributed among consumers in proportion to the area they occupy. That is, the readings of the individual meter will not affect the amount of payments by SDI.
How to pay for water supply?
It is necessary to timely pay for water supply and sanitation. In most cases, for this you need to take and transmit the meter, wait for the receipt and pay for the services.
Data Submission Dates
Existing legislation does not contain tightly tied to the date of the month dates for the transfer of data on housing services. The "Rules for the provision of public utilities" states that these terms must be defined in the contract.
Therefore, the period of receiving information for calculating the cost of resources consumed and forming a receipt is chosen by the water supply organization or the company managing the apartment building.
Typically, the deadline for submitting data from water meters is limited to the 18-25th day of the current month. But it is better to find out information about this period in the resource supplying organization.
Synchronous supply of information is needed primarily for the correct calculation of indicators that will go to the column "SOI". The deadline for submitting data for utility bills (including water) for December and April may be shifted to earlier dates due to the New Year and May holidays.
There are many ways to provide meter readings and they depend on the company that generates the receipts.
The following types of communication are commonly available and popular:
- phone call;
- SMS with a specific sequence of information;
- filling out the form online.
If the water consumer did not give information on metering devices on time, then automatically the average indicators for the last 6 months will be calculated. If the owner does not provide data within 6 months, then he can be transferred to a standardized payment, which, as a rule, significantly exceeds real consumption.
Payment Methods for Water
You can pay for water supply according to meter readings via the Internet, at a bank, or directly at the cash desk of a management or resource supply company.
Payment of utilities at the bank on the last day, as a rule, is accompanied by a long wait for their turn. Better to do it early or choose another way
If the consumer has a bank card with the ability to make online payments, the easiest way is to pay for utilities via the Internet.
There are several sites through which this operation can be performed:
- Unified Information Settlement Center (EIRC);
- state portal services (GIS housing and communal services);
- site of the bank that issued the card.
Everywhere you will need to register. You also need to know not only your address, but also your personal account number. After filling in all the data, the user will be transferred to the bank’s website, where it will be necessary to carry out the online payment procedure.
If this method is complicated or unusual, and the bank branch is close, then you can come there with a receipt. Payment can be made both at the cash desk (while the bank can take a commission), and at an ATM.
Sometimes, especially in small villages and towns where there is no bank, payment can be made at the post office or village council.
We also recommend that you read our other article, where we talked about the intricacies of the choice of water meters and gave a rating of the best devices according to users. More details - follow the link.
How to correctly take readings from a water meter:
One of the automatic reading systems:
Payment through Sberbank ATM using the receipt barcode:
Calculation of the volume of water consumed using these metering devices is quite simple. Knowing the tariffs for hot and cold water supply, you can calculate the sum of the costs for water and sanitation. Payment for services can be made at the bank, in the resource supplying organization or via the Internet. The last way will avoid queues.
If you have any questions regarding calculations or payment for water supply services, you can ask them in the comments box, and we will try to respond to them promptly.