The chimney is a necessary part of the heating system of a private house. It ensures the proper functioning of the furnace or boiler, organizes the removal of harmful combustion products outside the home.
We will try to figure out how to equip the chimney with your own hands, so that the heating communications are safe for both people and the house.
Chimney design requirements
The installation of heating appliances is subject to the requirements set forth in the regulatory documentation.
Installation of devices is regulated by provisions SNiP 2.04.05–91 and DBN V.2.5-20-2001. It is also advisable to study materials about heating systems (SNiP 41-01-2003), about heat generation devices (Airbag 252–98), on the technical conditions for the operation of thermal devices (GOST 9817–95), on the rules and regulations for the operation of smoke channels (VDPO).
The design of the chimney and the installation features must fully comply with the requirements specified in SNiP, otherwise you will not receive a certificate of verification of the structure, which is issued after commissioning
Part of the requirements is addressed specifically to the installation of chimneys. The construction of the structure can be anything, but the material of manufacture must be non-combustible.
The materials used for the construction of chimneys can be:
- steel;
- ceramics;
- brick.
Without exception, all designs are prefabricated, and the installation itself is fragmentary, since the chimney passes through several rooms (for example, a room and an attic).
In order for the structure to meet fire safety requirements, it is necessary to correctly calculate its parameters, as well as select all component parts in size. When installing factory equipment, it is necessary to comply with all the recommendations set out in the instructions, including the assembly procedure and methods of installation of parts.
Image Gallery
Photo from
Solid fuel brick pipe
Ceramic chimney with tee
Metal pipe - a cheap and easy solution
Chimney Sandwich Device
The documentation contains certain provisions that also need to be taken into account, for example:
- the length of the chimney can be any, but not less than 5 m (the height of the ventilation ducts is not less);
- the cross-section of the pipe must correspond to the inlet in the generator or exceed it;
- each heat generator needs a separate chimney;
- the speed of flowing air inside the pipe is from 15 m / s to 20 m / s;
- the thickness of the pipes is determined by the material of manufacture (the norm for steel is at least 0.5 mm);
- for regular inspection and cleaning activities chimneys are equipped with pockets (niches) with a depth of 0.25 m;
- the maximum number of turns of the chimney - 3;
- the radius of curvature must exceed the diameter of the channel;
- the height of the pipe above the roof is regulated by the roof structure: on a flat roof - 0.5 m; 0.5% higher than the roof if it is located at a distance of 1.5 m (or less) from the ridge; equal to or greater than the axis of the ridge, if located at a distance of 1.5-3 m.
The procedure for erecting the structure is established - always from the bottom up, that is, from the heat generator (boiler, furnace) through the ceiling to the roof. In prefabricated structures, each subsequent pipe part is introduced into the previous one.
The working temperature of the sealants used to fix the parts should be at least 1000º. Outside the connections are equipped with clamps, the mounting material should not fall into the chimney.
Supporting brackets are provided for fastening the tee, and in order to avoid channel bending, every 2 m on the wall it is necessary to fix the clamps to support the pipe
The normative documentation defines the places where it is allowed to install chimneys. The material of the walls must be non-combustible, but if this condition is not met (for example, in a building with wooden walls), then for installation, for protection purposes, pipe or crown pipes should be used.
Instruction for laying a brick chimney
The most ancient chimneys known to mankind were made of stone, and then of brick, together with the first stoves. To this day, natural material is used for the construction of heating systems in private homes. Consider the main stages of the construction of a brick chimney.
Brick Pipe Design Features
There are two options for connecting a brick pipe. The first, lighter, is installed directly on the stove, the second is built nearby and connected with an adapter. The fact is that the weight of a brick chimney with a height of 5 m or more is quite large, and not every heat generator can withstand it.
For the construction of one pipe, from 500 to 800 bricks are required (depending on the height of the ceilings and the roof), the weight of each of them is 3.8 kg.
In any case, the chimney is not just a hollow structure inside, but a complex structure consisting of several functional parts.
The working part of the pipe below the ceiling is the internal chimney. It starts immediately from the surface of the furnace (boiler) and ends at the ceiling itself (for 4 rows of masonry)
When the chimney passes through the ceiling, a fluff is arranged, which is a thickening. The following thickening of a similar configuration is constructed when the pipe passes through the roof. It's called "otter».
Part of the pipe from the cannon to the otter is the external chimney. Rises above the roof neckending with a head (alternative to a deflector).
The main safety condition is the distance from the internal channel through which hot smoke and gases pass to the surface of walls and floor elements. It equals 0.25 m - this is exactly the length of one building element, red solid brick.
The second condition concerns the location of the chimney. It must be erected strictly vertically, the maximum possible error is 3 degrees. And the third condition is the perfect tightness of the masonry, in which there should be no through holes and cracks.
The dimensions of the chimney depend on the power of the heater. Usually choose one of the traditional masonry: with the smallest section - “four” (12.5 cm x 12.5 cm), rectangular - “five” (25.0 cm x 12.5 cm) or large - “six” (25 cm x 25 cm).
The latter option is preferable for Russian stoves, rectangular - for fireplaces. For small stoves, the first solution is suitable.
Image Gallery
Photo from
The brick chimney is, in technical essence, a continuation of the system of chimneys - chimneys formed during installation of the unit
In the upper part of the stove, chimney turns are closed by a ceiling. There is only one chimney channel left, in our example there is also a tap to the heat exchanger
Chimney masonry is made with the obligatory observance of dressing. The thickness of the joints should not exceed 5 mm, the excess solution should be removed immediately
In order to prevent flue gases from “escaping into the chimney” and to heat the attic space, the brick stove can be equipped with a heat exchanger - a Tunguska with a water boiler
Those wishing to use a metal sleeve in the smoke channel should remember that it must be installed at the entire height of the chimney, and the channel itself should not be narrowed more than 1/8 of its cross section
When using a metal sleeve in the attic area, it is not necessary to plaster the brickwork around it, which is done to determine flue gas leaks
If in the area of the cold attic the metal sleeve is not planned to be bricked, it is insulated with non-combustible material: mineral or glass wool
The metal parts of the combined chimney, for example, the chimney from the tunguska, are laid in fireproof boxes, which are closed with metal sheets
Brickwork with smoke
Old chimney construction row
Construction of a chimney in the attic
Connecting the heat exchanger to the chimney
Chimney brick liner
Building a brick pipe metal
Mineral wool insulation pipe insulation
Arrangement of metal parts of the chimney
Material selection and solution preparation
The stove chimney is equipped with a brick stove. If another unit is installed, then the pipe is built up after its installation. For construction, you will need a brick and mortar, as well as tools: a trowel, a plumb line and a special hammer for tamping.
Bricks are pre-soaked. For the device of flaking and otter, pieces of bricks of ½, 1 / 4.1 / 8, размером in size will be required.
To ensure that the parts of the bricks are smooth, and the cutting process takes place without excess dust, we recommend using a circular saw with diamond interchangeable circles
The usual cement mortar is not suitable for masonry, a mixture of clay and sand is needed. This is justified by the characteristics of clay, which has a linear expansion coefficient close to brick parameters. Depending on the type of clay (lean or oily), its ratio to sand may vary: 1: 3 or 1: 4.
Clay is pre-prepared - soaked in water and kept for about 3 days. Before use, the material should have a consistency resembling liquid sour cream, and not have foreign impurities. Special requirements apply to the sand. The best option is rough, with grains of 0.9-1.0 mm.
Clay and sand are mixed in small portions during masonry. Sometimes you need to add water. The quality of the solution can be easily determined by the way it contacts the trowel: the mass should leave marks on the surface, but not drain from it and not stick in large pieces. If you have problems with self-preparation of the mixture, you can buy a ready-made one.
The laying order of the main parts
If the boiler is installed or the furnace is finished, you can start to build a brick chimney. The working procedure is traditional: applying the mortar, then installing the brick, adjusting it relative to neighboring parts with your hands and a small hammer.
The vertical position is checked after laying each row with a plumb line. The width of the wall is 12.5 cm. The straight pipe element is completed 4 rows before the flare - expansion in the ceiling.
To expand the thickness of the walls, it is necessary to fold 4 rows one above the other, so that each subsequent one moves by 1/8. What parts of the brick is better to take - indicated on the diagram
It is necessary to exclude the pressure of the ceiling structure on the masonry, so a gap of 2-3 cm wide is left between the overlap and the fluff. It is used for the installation of insulating material, for example, mineral wool plates.
A straight section of the pipe again passes through the attic, then an otter is made. Its bottom row must be laid out when the outer edge of the chimney has passed through the roof. At this stage, cement is often used to prepare the solution, more durable and wear-resistant than clay.
The otter consists of 6 rows, the indent of each following is 1/8 of the whole brick. The holes around the pipe are insulated and covered with steel roofing sheets.
The next stage is again straight - the neck, which is crowned by the head.
The shape and size of the head may vary, but the traditional version is two rows, the first of which is shifted 1/8, the second - ½ from the whole brick
A chimney is required for the chimney so that puffs of smoke do not return back into the chimney. Along the perimeter of the head mount mounts for the cap - protection against precipitation. Caps are often used as an element of decor, so they are given an interesting and beautiful shape.
Ceramic chimney construction
Prefabricated ceramic chimneys have become popular due to their strength, safe composition, environmental friendliness, ease of installation. They borrowed the best technical specifications from steel and brick models. The only negative is the high cost of the kits. Consider how a chimney made of ceramic in a private house occurs.
Prefabricated Type
Unlike brick chimneys, ceramic is mounted already from the finished elements, gluing from each other with a special solution. It is not possible to make ceramic parts yourself; ready-made kits are purchased for construction.
Manufacturers present standard kits from which you can assemble a chimney for a fireplace, stove or boiler.
An element of a ceramic chimney is a section of a pipe. Pipe sizes vary from manufacturer to manufacturer, one of the standards is 3 pieces per 1 meter of chimney
In addition to ceramic pipes, the kit includes the following parts:
- base element with condensate drain;
- a part for connection with a nozzle (angle 90º or 45º);
- revision chamber with a door;
- lightweight blocks for external framing;
- set for external design (on the roof);
- non-combustible insulation material for installation;
- paste glue.
Additionally required fasteners (brackets) and non-combustible material for cladding: plaster, natural stone, ceramic or clinker tiles.
Image Gallery
Photo from
The technical term "ceramic chimney" is the definition of a three-layer system, the outer part of which is made of a ceramic-concrete shell, the inside is a ceramic channel. Mineral wool insulation is laid between the sheath and the channel
At the corners of expanded clay concrete blocks there are holes in which reinforcing bars are installed. they serve as guides and provide structural rigidity
The ceramic chimney system is assembled on a modular basis from elements prepared for installation. The main thing is to ensure the tightness of the joints
The passage through the roof structure is arranged according to the rules for a brick pipe. The gap around the chimney is blocked by a duct with mineral wool
The part covering the mouth from precipitation is equipped with a cone, slightly narrowing up. This solution reduces atmospheric moisture penetration into the system.
Mainly chimneys are constructed from blocks with a ceramic pipe, to which the stoves are connected with a brick or metal section of the pipe. A wide range of stone cladding materials has been proposed for facing the ceramic walls of the chimney
In order to be able to check and clean the chimney, revision chambers are arranged in it for which elements of a special design are produced. Ceramic tees are installed in the duct for cleaning and connection.
For the gate device, a tee and an external metal panel with a movable gate valve are installed. It is needed to adjust the size of the cross section of the chimney hole
Ceramic chimney system
Installation of metal guides
The modular principle of the assembly of the chimney
Ceramic pipe passage through the roof
Detail for the mouth of a prefabricated chimney
Root pipe construction
The device of the audit chamber
The specifics of the organization of the gate
Assembly and installation rules
According to the norms of installation and operation of a ceramic chimney, it should not be further than 2 m from the heat generator (the closer, the better), as far as possible from walls and ceilings of combustible materials, and should not cross the supporting elements.
During installation, you must adhere to these rules:
- a prerequisite is the construction of a foundation covered with a fire retardant;
- installation begins from the bottom - the base, then sequentially continue towards the roof;
- the parts are glued together with a special glue, which is included in the kit;
- the diameter of the pipe should be larger than the outlet pipe of the heat generator;
- for thermal insulation use mineral wool and plaster;
- the junction of the pipe and the roof is protected with a metal apron;
- if the roof is covered with combustible material, it is necessary to equip a spark arrester.
If the chimney channel is installed without fasteners for more than 3.9 m, it must be reinforced with steel rods. Especially for this purpose, holes are provided in the pipe parts at the corners.
One of the design options for the ceramic channel. The thermal insulation layer increases the degree of protection, the outer cladding serves as a barrier between the combustion products and the building elements
The upper part of the head is equipped with an umbrella to protect from rain, debris and strong winds.
The nuances of installing and connecting pipes
The elements from which the chimney is assembled are made of ceramics with the addition of chamotte - this composition tolerates high temperatures, and parts from it have a long service life. They cannot be used as independent units; external protection is absolutely necessary.
The lower part of the chimney - the base - is equipped with an opening for the removal of condensate, which is formed during the removal of combustion products. The accumulated liquid moves to a sewer that has been supplied in advance.
It should be remembered that moisture from the chimney is detrimental to the bacteria of the septic tank, so it is better to prepare a separate container to collect the liquid.
A tee with a revision hole is installed on top of the base. During fuel combustion, the hole is closed by a door. The main purpose of the tee is the ability to inspect and clean the chimney
Elements are installed on top of each other according to the instructions, without changing the order established by the manufacturer. Correspondence of the dimensions of the chimney and the parameters of the house must be checked in advance.
How to cook and apply glue?
In order for the chimney parts to be hermetically connected, a special acid-resistant glue is used. This is a thick mixture, which is prepared manually from dry powder and water in a ratio of 7: 1, preferably at room temperature.
At first, the solution looks unusually dry, but after about 7-8 minutes it acquires the necessary pasty appearance.
The finished mixture must be quickly and accurately applied to the junction of pipes, trying to use within an hour and a half. Then it loses the necessary properties, and it is impossible to breed the drying mass with water
One of the nuances of applying glue is the preliminary wetting of the ceramic surface. It is impossible to save the adhesive mass - only hermetically filled seams guarantee the full functioning of the chimney.
The remaining glue must be removed: from the inside - so as not to accumulate soot, from the outside - for aesthetic purposes.
If subsequently there is a desire to mask the pipe with a decorative partition, a technical inspection hole should be available.
The device of a metal sandwich chimney
Steel chimneys are popular both in industrial construction and for the improvement of the private sector. Their installation resembles the assembly of a ceramic structure; accordingly, it is easier than building a brick pipe. Let us consider in more detail how to properly make a metal chimney, avoiding errors.
Materials for the installation of metal construction
Sandwich chimney is a sealed system of pipes and adapters leading from the heat generator to the roof space. It can pass inside the building (internal) and outside, along the wall (external).
A sandwich pipe is a three-layer part consisting of two steel pipes, between which a layer of insulation is laid. Fragments of stainless steel connected by welding
Non-combustible heat-insulating material has a different thickness - on average from 2.5 cm to 10 cm. Manufacturers most often use one of the best materials - dense basalt cotton wool (from 200 kg / m³).
To assemble the chimney, you need to connect several parts of various shapes, using the method of connecting the narrowed ends and sockets. Simply put, one element is inserted into another. On the outside, the joints are reinforced with overhead clamps, which tightly tighten after installation.
Advantages of the three-layer design: protection of the chimney duct, minimal condensation, organization of stable traction, the possibility of installing the system from both the inside and the outside of the house
When installing a steel chimney inside the building, the openings in the ceilings and the roof are much smaller in diameter than for brick or ceramic counterparts.
Installation diagrams of a sandwich chimney
Consider two schemes for installing a sandwich chimney: with an internal arrangement that requires the organization of holes in the roof and ceilings, and with external installation, which is carried out from the outside and installed parallel to the wall of the house.
Each of the schemes has advantages: the internal equipment forms less condensate, the external device is easier to execute and is made with the device with only one hole
The internal installation scheme is often used in bathhouses, since a steel pipe can simultaneously heat both stones and a tank of water. If the bath is not installed separately, but is an extension to the house - this is the most appropriate and effective option.
The disadvantages of the internal system are the need to make holes in the ceilings and the roof, as well as a decrease in usable space.
To install an external system, it is enough to make one hole in the wall and provide a vertical arrangement of pipes using brackets. Piping out reduces the risk of poisoning from combustion waste. Minus - arrangement of additional protection from the effects of the external environment.
Installation procedure:
- connection to the boiler (or other heat source) adapter;
- punching holes in the wall (average size - 40 cm x 40 cm), upholstery with fire-resistant material;
- installation in the wall of the passage block with thermal insulation;
- installation of a horizontal pipe segment from the boiler (furnace) to the hole in the wall;
- arrangement of the support node from the outside (platform on the brackets);
- installation of a vertical pipe;
- mount at the top of the cone and head.
When assembling, it is necessary to focus on the technical documentation prepared in the process of compiling the project.
Inside pipe tips
When choosing an internal model, it is necessary to remember some technological nuances. For example, it is important to install a valve in the transition section from the boiler so that it is possible to retain heat.
Docking of two adjacent elements in the transition area is prohibited. The location of the attic rafters and beams should be taken into account: the further they are from the chimney, the better. Read more about self-assembly of a sandwich chimney in this material.
Transitions through ceilings and roofs require the use of fireproof heat-insulating materials, for example, mineral wool, and the construction of protective blocks, which can be called a “sandwich in a sandwich”
To imagine how the installation process of chimneys of various types occurs, we offer useful and informative videos shot by skilled craftsmen.
Do-it-yourself brick chimney:
Stages of installing a ceramic chimney brand TONA:
Tips for installing a sandwich chimney:
The construction of a chimney for a gas boiler, stove or fireplace is a responsible task requiring special permission, designing and professional skills. If you are not confident in your abilities, entrust the installation of the pipe to specialists who will perform the work taking into account all norms and requirements.
If you already had to build a chimney yourself or you are an expert in this matter, please share your experience and knowledge with our readers. Tell us about the nuances of building a chimney in the block below.